2019 - Applied Energy

Sub Cooling and How to Troubleshoot A Central Air System

June 7, 2019June 7, 2019 Kelly YoungCooling

Understanding Subcooling …

Let’s go back to basics for a moment to make sure we understand what subcooling is, to begin with. During a refrigeration cycle, high-pressure super-heated gas is converted by the condenser into high-pressure liquid so the evaporator may use it for cooling purposes. It does that by removing enough heat out of the gas in order to cause it to condense into a liquid at the prevailing temperature and pressure (saturated liquid point). Any of the added heat that is removed from the condenser is referred to as “subcooling.” The amount of cooling that may be measured at the condenser’s outlet is a good indication of the performance of the condenser.

When the condenser is operating in an efficient manner, the process of the refrigerant vapor being converted into a liquid is completed prior to the refrigerant reaching the final several passes into the condenser coil. Those several last passes should be only filled with liquid. Since the coil is transferring heat still, from the liquid refrigerant into the last couple of passages, the temperature will continue to drop and subcooling of the refrigerant occurs.

Subcooling is an accurate measure of the amount of time it takes for the refrigerant to pass through the condenser. This is referred to as “stay time.” The proper amount of subcooling for any specific unit may vary with its application and type of system. Subcooling may fall within the 10 to -20 F range with design air flow, clean coils, and at the right charge.

How can subcooling assist with troubleshooting?

Knowing all of that, how can subcooling assist with troubleshooting? Let’s take a look at a few different situations. When there is an insufficient refrigerant charge in a system (under-charged unit), that will cause the refrigerant to flow quickly through the condenser to attempt to satisfy the load conditions. That doesn’t allow a sufficient amount of “stay time” to let the refrigerant condense and be subcooled properly which will result in no or little subcooling.

A system with a plugged or improperly adjusted valve, on the other hand, will exhibit very high subcooling (perhaps 30 F) due to all of the excessive amounts of liquid backing up into the condenser. The strange part about both of those situations is they have the same effect on the system’s evaporator side: high super-heat, low head pressure, and inadequate cooling.

How do we tell what the problem is exactly and how do we properly diagnose it?

There are 2 different situations here that cause the same problem on the system’s evaporator side. So how do we tell what the problem is exactly and how do we properly diagnose it? The only way to know what the exact cause of the problem is to take a subcooling measurement to pinpoint it without having to rely on trial and error processes. When a subcooling measurement is made, the technician can potentially prevent having to do an unnecessary change-out of the expansion valve. If there is zero subcooling, the expansion valve cannot close due to a plugged orifice or lost bulb charge.

If super-heat is high and subcooling is low, you can assume there is most likely a low refrigerant charge. In order to double check your assumption, take a measurement of the compressor amp draw. It should be a low reading. There should also be a low-temperature difference across its coil.

An example of how subcooling can assist with troubleshooting …

The following is an example of how subcooling can assist with troubleshooting.

When subcooling is used properly it can be a valuable tool that can significantly reduce the amount of time that is needed to diagnose system malfunctions. In addition to suction super-heat, it is playing an increasingly important role in maintaining and servicing an air conditioner or refrigerant system. Above I just provided you with a few scenarios – can you think of other areas that it could be invaluable for you in making a diagnosis?

Be sure to look at all sides …

It is important to always keep in mind that an air conditioner is a system. All sides of this system need to be looked at – air flow, evaporator, condenser, etc. All of them deter from or contribute to a system operating correctly. Doing a complete diagnostic will allow you to solve problems.

Is It Time for A New Air Conditioner?

June 7, 2019June 7, 2019 Kelly YoungCooling

Three signs it might be time for you to get a new air conditioning unit

Summer is right around the corner, and that means the time has come for you to think about your air conditioner. If your AC unit is getting up there in years or just doesn’t use the latest in technology, and it seems you’re calling for an AC repair every year, then the time might have come to get a new one. This air conditioning repair service company in Kingston / Gananoque points out the three signs it might be time for you to get a new AC unit.

Increased Costs and Reduced Efficiency

As with any machine, when an AC unit gets older, it wears out more. Just like with a furnace, a lawnmower, or a car, the increased wear and teary can equate to a decrease in efficiency. In regards to air conditioning unit, this would mean it has to run longer just to get to the same temperature level it might have gotten in just half that time several years ago. Be mindful of your electric bill. Should it keep climbing, you need to contact our air AC company. It might be possible that the unit just has to get repaired. However, if we’re able to trace the issue to the age of the unit, then you need to consider buying a new AC unit.

Repairs Cost More

Even machines built better than others are going to need routine repairs and maintenance in order to keep smooth operating levels. However, as age creeps up on the performance of an air conditioner, it’s possible that you’ll start seeing the very same parts needing repair with a growing frequency. One instance could be the heat pump of the AC unit. If you wind up calling to get service on this particular item multiple times per year, then that’s a definitive red flag. If things get to the point that you start winding up getting repairs for more than one item, it probably makes sense to stop wasting money on individual issues and just buy yourself a new air conditioner. The frequency with which system failures happen goes up with age, which means you’re smart to just deal with things directly instead of continuing to sink money into something that isn’t going to be fixed.

More Than 15 Years Old?

At this point, you’re likely wondering what the average lifespan of most AC units is? The short answer is typically 10 to 15 years. This is of course based on the kind of AC unit you have, the frequency with which you run it, and if you clean it periodically or have parts replaced as need be. If you have an AC unit that reaches 15 years of total service and is still running really well, then consider yourself fortunate. Just be ready for what is likely going to be a sudden downshift in its performance level.

You have two choices here, as already alluded to. You can work to get every last minute of service from your AC unit by keeping up with services and repairs. Alternatively, you can invest into a new unit. In the end, it’s a lot more cost-efficient to just buy a new AC unit, although homeowners typically have timetables of their own based just on usage, budget, their current AC unit, and the like. If it makes any sense to you to push your current unit for another few years, then by all means do so. However, don’t flush too much money down this hole, and keep in mind you’re going to need a replacement anyway.

If you want more information about AC installation, repair service, or longevity, then consult an experienced air conditioning professional.

7 Tips to Repair Your Home’s Heat Pump

June 7, 2019 Kelly YoungCooling, Heating

Heat Pump Repairs ….

Winter’s is over, so I’m quite sure everyone is looking ahead to the finale of this heating season. Even though the title mentions heat pumps, this could really apply to any equipment that’s out there. It really just boils down to competence, which comes from knowledge and training. You can see how this might apply to nearly anything if you swap out heat pump for whatever kind of equipment you focus on, be it furnaces, packaged units, or what have you.

Everyone gets hit with a heat pump which just doesn’t work. It happens sooner or later. The issue might be a defective part, old age, misuse, or just a loose connection.

Are you a service technician?

If so, then you want to try these following techniques. They’re not actually guaranteed to give you results, but they’re certainly going to give you something to do as you figure out how much you’re going to charge your customer 🙂

STEP 1: Approach the heat pump in a confident manner. This will tell the machine, mistakenly, that you know what you’re doing. It should also impress anyone watching, so if the heat pump suddenly starts working, you’re going to be credited with the successful repair. If this doesn’t work, move on to STEP 2.

STEP 2: Wave the manufacturer manual at said heat pump. That should make the heat pump assume you’re familiar with the source knowledge. If that fails, move on to STEP 3.

STEP 3: Forcefully recite OHM’s Law to said heat pump. (Before you take this step, make sure you actually know Ohm’s Law.) This will definitely prove your knowledge to the heat pump. Is the machine still unimpressed? Go to STEP 4.

STEP 4: Slightly jab the unit. That might involve a 3- or 6-lb. hammer. On the other hand, you need to be careful in this step, so you don’t damage the pad.

STEP 5: Wave around a large screwdriver menacingly. This shows the machine that you personally know the fatal short-circuit technique.

STEP 6: Should nothing else work, just add a bit of refrigerant. This will now confuse the heat pump, thereby increasing your advantage.

STEP 7: If that heat pump doesn’t have any sentimental value and you’re just done messing with it, then it’s time to sell a new model. On the other hand, if you’d like to make some last-effort in saving it, then call your preferred factory representative. Also, avoid displaying any further ignorance by giving the customer a bill right now.

Electric Wall Mounted Heaters

May 21, 2019June 13, 2019 Kelly YoungHeating

Advantages And Disadvantages Of Electric Wall Heaters

Electric heaters come in handy in keeping your home or office comfortable and especially in cold weather. Electric wall heaters are not only easy to use and convenient but also very affordable, making them a preferred option by many. It’s however advisable to research and look into the features of the wall heater before making an order. Outlined below are some of the advantages and disadvantages of wall mounted electric heaters you ought to know of.

The Advantages

Electric wall heaters come in many shapes and designs. It’s advisable to choose just the right heater for the desired application and preferences. Here are the advantages of electric wall heaters.

Cost: Electric wall heaters are affordable and do not waste energy either. You should notice reduced heating bills after switching to this heater.
Safety and ease of use: Electric wall heaters are relatively easy to operate. You simply plug in and turn it on. These heaters come with two built-in security features to ensure your safety. They have sensors that turn the entire system off completely if an object comes too close to the heater. In addition to this, the heater doesn’t get too hot to cause combustion.
Compact size: The heaters are small enough to fit in the smallest of rooms, including bathrooms and offices.
Instant heat: Once turned on, the heater warms the room fast enough, thus leaving you comfortable. You should, however, keep the door closed for faster heat distribution.

Disadvantages

Short cords: The power cords can be a little too short when installing the system. The main idea behind short cables is to keep them hidden.
It’s only efficient in small spaces: Electric all heaters are exclusively designed to heat small areas. This means you cannot use the heater in larger spaces and homes. You’ll need several of these heaters to keep a large room or house warm.
Doesn’t use duct-work: Electric wall heaters do not use ducts to disperse heat. For this reason, it might take longer for a room to heat up to one’s preferences. This is, however advantageous in that; no allergens will be blown in your direction.

Notable Features Of Electric Wall Heaters

Energy efficient heating: These heaters use superior technology to circulate heat in the desired space. The low wattage means reduced heating bills for the heater only uses 4 cents per hour. This translates to 50% less energy usage.
Ultra-Safe Wall Mounted Heaters: This feature makes it possible to leave the heater unattended for hours. The heater comes with an auto shutoff technology which powers the system down on contact.
Healthy Heating: Electric wall heaters run silently, and have an auto-dimming power light that allows you to sleep well at night undisturbed. In addition to this, the hypoallergenic and fan-less design means no allergens and dust will be circulated in the heated space.